The ESP32 records and posts the signal strength of the wireless network that it is connected to. Press a button on the board to take three measurements of the wireless network signal strength and post the average result to a ThingSpeak channel. The device also posts a. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features Press Copyright Contact us Creators. An IR signal is modulated. To understand the data you need to demodulate the signal. The simplest way is with an IR receiver module. However they condition the signal into a digital signal - it's impossible (on the majority of modules) to get the signal strength. The devices you link to are IR Photodiodes.

Esp8266 Get Signal Strength
Esp8266 Signal Strength
Esp8266 Read Signal Strength
Esp8266 Measure Signal Strength

Project source code at GitHub: iridium-signal-strength-monitor

In a previous article, I wrote all about Iridium satellite communication for IoT projects using an Iridium modem and simple Arduino technology. However, when trying to send a message to a satellite constellation, you never know if the message will go right away or if it will take several minutes. Sometimes there is a satellite overhead, but sometimes you will have to wait a while before one flies over you. Max payne games. I decided to investigate how the signal strength reported by the Iridium modem (AT+CSQ command) correlates to the actual positions of Iridium satellites. So I used the amazing CesiumJS open source JavaScript library and the hardware I built in the previous project to make a great tool that shows how signal strength matches up with the satellite positions! Understanding the reception quality of satellite constellations is going to become increasingly important as companies like SpaceX roll out their low earth orbit (LEO) Internet connectivity solutions like Starlink.

How It All Works

There’s a lot going on here, so let me explain. First, I deployed my simple development board that I built before but this time I connected an ESP8266 to the serial line so that it could send information to the Internet. The Arduino code on the dev board uses the Iridium SBD library to ask the modem for the “signal strength” that it has at the moment. This gives a value from 0-5. It writes this info over serial to the ESP8266 which publishes it to an MQTT topic. So basically this sits outside with the antenna pointed to the sky and asks the modem every 5 seconds what the signal strength is. The GPS module allows me to attach an accurate timestamp to the reading so that the data can be matched up with the satellite position info.

On the software side, I wrote a web tool using CesiumJS that displays the orbits of all the Iridium satellites. It calculates the orbits from the Iridium two-line element sets (TLEs) from Celestrak. CesiumJS is a great way to visualize orbits and show the positions of satellites in realtime. You can zoom in, pan and tilt the globe, OMG it’s just gorgeous. The web client is served up from a simple NodeJS server that also subscribes to the MQTT topic to get the signal strength data as the hardware publishes it. The server sends the data up a websocket to the web client.

In addition to showing the realtime satellite positions and predicted orbits, the web tool also:

displays the current signal strength as 5 bars, just like your phone
calculates the closest satellite to the ground station and renders a green line to it
displays the footprint of each satellite. You can change the elevation angle using a slider. When set to zero, the footprint represents visibility to the horizon. I have found that setting this to 25 degrees gives a more accurate depiction of the satellite’s communication range. That is, my hardware can “hear” the satellite if it is at least 25 degrees above the horizon.
plots the signal strength vs. the distance to the closest satellite on a scatter plot. This should show that higher signal readings are correlated with shorter distances to the closest satellite.

Results

Well, does it work? Does the signal strength reported by the modem correspond to the actual proximity of an Iridium satellite? Yes, it does! It’s not perfect, but this is RF, so one should not expect perfectly predictable measurements. There are all kinds of factors at play in RF propagation. But generally speaking, I measure zero bars when there are no satellites overhead, and measure a stronger and stronger signal as a satellite approaches. The scatter plot that is built up over time definitely shows that strong signals (vertical axis) are associated with smaller distance to the closest satellite (horizontal axis).

This video shows the experiment in action. The great thing about building a CesiumJS model is the ability to have all the data stored in a time series that you can play back at different speeds and even play it backward. Since satellites move slowly, it’s very helpful to back up in time and play the sequence forward at higher speeds. And it looks beautiful, too!

Waterfox 68. The latest and greatest version of Waterfox. Minimum Requirements. Waterfox is a 64-bit version of Firefox. The browser's developers modified the Firefox source code specifically for machines running 64-bit versions of Windows. Waterfox supports the Chrome Web Store, the Opera Web store and the Firefox Store. The most extension support of any browser! Everyone likes to use their browser in a specific way. Tab above address bar. Tab below address bar. Tab at bottom of browser. The official Waterfox 💧 source code repository. Contribute to MrAlex94/Waterfox development by creating an account on GitHub.

Software

You can try this yourself if you have an Iridium modem like the RockBLOCK 9603 modem. Or you can use the CesiumJS orbit visualization for your own projects. GitHub repo: iridium-signal-strength-monitor

Even if you don’t have the hardware to measure signal strength, you can use the the CesiumJS web application to show the realtime positions of Iridium satellites.

Here are some things you will need to change in the software if you want to do this project:

Esp8266 Get Signal Strength

In the code for the ESP8266 MQTTWiFiGateway.ino:

For the webserver and CesiumJS web application, set your MQTT server and credentials in server.js:

Esp8266 Signal Strength

You will need to get a Cesium Ion access token. It’s free.
Set your Cesium Ion access token in app.js:

Esp8266 Read Signal Strength

To use the MapBox dark imagery like I did, you’ll need to get a MapBox access token. Also set in app.js:

Esp8266 Measure Signal Strength

Installation and startup: